Tag Archives: small sailboats

A Journey Begun

Three years ago, today, May, 3, 2017, I set out from Ft. Lauderdale, FL., on my little Venture22 sailboat and eventually ended up anchored at the southern end of Anna Maria Island over on the Gulf side of the peninsula.

first day

 

The original destination was to be Breton Island, Louisiana, where I’d worked running a crew boat in the Kerr-McGee oil production field back in ’77/’78. I actually LIVED on the island for nearly a year…working 7 days on and 7 days at home.

Back then the island was about a half mile long and, perhaps, a quarter mile wide at its widest. But over the intervening years hurricanes had reduced it to a sand spit a couple of hundred yards long. I wanted to see it.

breton

I made it as far as Carrabelle in the eastern panhandle of the state.That’s where, 18 miles off the coast, on July 6, 2017, a Coast Guard-dispatched boat took me aboard their boat and dropped me off at the dock in Panacea, Florida where an ambulance was waiting to take me to Tallahassee Memorial Hospital suffering from total kidney shutdown due to severe dehydration. I spent 17 days at TMH and Health South, a rehab facility, until I’d regained enough strength before returning to the boat to continue my voyage. I decided to head south.

rescued

I made it to Bradenton Beach and Anna Maria Island where I’ve been ever since with one excursion, last year, to Cayo Costa to the south. About a 200 mile round trip.

95892932_233310454761404_1467145409381007360_n

92376835_3774458992596645_2369215732702511104_n

Comments Off on A Journey Begun

Filed under Anna Maria Island, boats, Bradenton Beach, FL, Coquina Beach, cruising, Living Small, Microcruising, Minimalist Cruising, Retirement Afloat, sailing, Small boat cruising, Small Sailboats, Uncategorized

New Boat?

Okay, this is the boat my friend went to look at in Miami this morning.

It’s a MacGregor 25 with a pop top and a swing keel. When the pop top is raised there’s 6-foot headroom in the after part of the cabin. The swing keel raises and lowers. With the keel down the boat draws nearly five and a half feet. With the keel fully raised it needs less than two feet of water to float, perfect for the shallows of the Gulf Intracoastal waterway and the Florida Keys. The boat can be taken right up to the beach.

This is what a pop top does

There are canvas attachments that enclose the pop top when it’s up but I don’t think this boat has one. I was thinking that a modification could be made with thin plywood and plexiglass, though. And the boat also has a Bimini top…

Cosmetically it needs work as you can see, but it’s nothing that bothers me. Four or five short days and all that blue non-skid can be made right. I’d paint it a sand/beige using a one-part polyurethane paint. I used Interlux Brightside in the cockpit of my Kaiser 26 and it held up remarkably well. Very resistant to abrasion and it retained most of its gloss over six years. Of course when painting the topsides you want to use a non-gloss paint to cut down on reflection.

The cushions are all in good shape which is rare for these older boats. The outboard motor needs to be tuned up. One of the major problems is that non-boaters shut the things off and the gasoline sits in the carburetors and evaporates leaving gummy residue. What needs to be done if the boat isn’t going to be used for a while is to disconnect the fuel and let all the fuel burn out leaving the carb dry. Also when outboards, or any boat that uses circulating water to cool the engine,  sit for a long time the rubber impellers that pump the cooling water deform so they need to be replaced.

None of that is a problem. Stef is a first-class mechanic and when we had out repair business in Fort Lauderdale years ago I can’t even begin to tell you how many times we did this kind of work.

As the French author, Blaise Pascal, famously said, “I would have written a shorter letter, but I did not have the time.”

Here’s how I found out what kind of a mechanic Stef was. When I got back from France and cruising down to Guatemala back in ’92 I was at loose ends and needed some kind of work. Stef had a ski boat on a trailer in his car port and I said, “Why don’t we paint that up and sell it?” He said that the engine, a Ford V8, wasn’t working. A minute later he said, “Listen, come back around 8 in the morning and we’ll get this thing together.”

When I showed up he had a hydraulic motor lifter

and an engine stand.

That’s something you bolt the engine block to and you can move the engine around to reach all parts of it without having to bend over. It took us less than an hour to get the engine out of the boat and onto the stand. Then Stef started disassembling the motor and throwing parts into a couple of 5-gallon buckets. All I could think of was that he was a fucking mad man. The only thing he did that seemed at all normal was he placed the pistons carefully on a work bench in the order that they came out of the block. When everything was off the engine he said, “I’m going to go to ‘Engine Rebuilder’s Warehouse’ and get what we need. While I’m gone you take all those bolts that are in that bucket and clean them up with this wire wheel on the electric motor.”

When he returned he showed me how to hone the cylinders with a special tool on a drill motor

 

and while I was doing that he laid the bolts out on the work bench according to size. With that done he started putting the engine together. New bearings and guides and all that good stuff. We broke for a quick lunch and then finished up. The ONLY time he consulted a manual was when he was looking at the torque specs for the piston ends and the head bolts. The engine was back in the boat in a flash, and at around 4 o’clock in the afternoon he turned the key and BRRRRRRROOOOOM, the damned thing started right up. TO ME that was like MAGIC!!! Over the next several years we probably rebuilt a couple of dozen engines. With a manual at hand I wouldn’t be afraid to tackle a rebuild on my own. I later found out that he used to have a xmall chain of engine rebuilding shops in New York for VW engines. The deal was, get it in by 8 in the morning and you could drive home with a rebuilt engine after five in the afternoon.

So, anyway, there’s a nearby marina where we can store the boat for $300/month (that’s TWO MONTHS apartment rent here in Boquerón). Stef says the engine is practically brand new, it’s just been sitting. He can take it up to his warehouse in Ft. Lauderdale and do the tune up there.

The asking price is $1,300 for the boat and $1,300 for the motor. Stef told him that was a bit too much for condition of things and Fernando agreed. The way Stef left it was he was going to send me the pictures and see what I wanted to do. As I told him, there’s nothing I can’t take care of. Sure, the life line stanchions were removed, but they’re on board and it’s only a matter of drilling 16 holes to get them reattached. Certainly no biggie there.

There will be a lot of things that I’ll need to buy to make the boat what I’d really like it to be, but it doesn’t have to all be done at once. That’s one thing a lot of people never understand. They aren’t comfortable with the “that’s good enough philosophy.” For them everything has to be exactly “just so” before they feel they can cast the lines of the dock. That’s why so few people actually GO SOMEPLACE on their boats. And, too, a lot of the stuff I’ll need, like the paint, etc., I can get wholesale through Stef’s account at Lewis Marine, one of the largest marine supply companies in the country. They ship worldwide, so things won’t be as bad as they might be for some people of limited means.

Stef’s going to call Fernando tomorrow and offer him $2,500 for the whole shebang. He’ll probably take it. I told Stef that if he balks go for $2,700 which is $500 off the asking price. I can certainly live with that. I’ve talked with Fernando via Skype and Stef, of course, in person, and Fernando is an anxious seller. He’s had the boat up for quite some time though he stopped advertising it a while back.

3 Comments

Filed under Uncategorized

Puddle Duck Goose

As my regular readers know I love the Puddle Duck Racer. It’s an ugly but easily built boat that can get you out on the water for a couple of hundred bucks and a couple of weekends worth of work. The web site proclaims: “The PDRacer is a one designe racing sailboat that is basically a plywood box with a curved bottom, and is the easiest boat in the world to build. Free plans, free club. The rules are aimed at keeping the lower 10″ of all hulls the same, but the rest is up to the builder. A simple hull can be made from 3 sheets of plywood, Titebond II glue and latex house paint. If you work hard for two weekends you can go sailing on the 3rd weekend.”

I doubt there is a group of sailors anywhere in the world that have more fun than the owners of these boats. Many have made some remarkable voyages in the Texas 200 the last couple of years and no matter what kind of boats the other participants of the 200 are sailing it seems everyone pulls for the little guys.

Back on October 22 I wrote about a “cruising” version of the boat and suggested that I thought the PDR Goose would be more suitable for a minimalist, easily built inexpensive boat. I did not, however, explain what the Goose was.

The PDR Goose is a stretched-out 12′ version of the PDR and it’s fast building its own following. The Racer has a Yahoo site for its devotees,http://groups.yahoo.com/group/pdracer the Goose recently formed one, too: http://groups.yahoo.com/group/pdgoose/ Unlike the PDRacer, the Goosers (oooooo, that tickles) do not want  the boat to become a racing class. They’ll leave that to the one-design class PDRacer. Hey, the boats are cheap and there’s no reason you couldn’t have one of each. The advantage of the larger Goose is that you can more comfortably take along additional crew on your adventures.

This morning in one of my favorite boating blog sites, Duckworks, there was a post in the next-to-last article giving a link to several YouTube videos of a completed Goose under sail. While  the Duck is rather clunky having a length to beam ratio of only 2:1 at 4’X8′ but the elongated Goose is 3:1 at 4’X12′. Not only does it look good it seems to sail great as seen here.

And it will get up and plane:

To see more videos of this nice craft underway click this link:

http://www.youtube.com/results?search_query=pdgoose&aq=f

Plans can be downloaded from Duckworks here: http://www.duckworksbbs.com/plans/storer/pgr/index.htm. A good story with lots of photos on the building of a Goose.


Comments Off on Puddle Duck Goose

Filed under homemade boats, Microcruising, Minimalist Cruising, PDGoose, Puddle Duck Goose, Puddle Duck Racer, sailboats, sailing, Small boat cruising, Small Sailboats