Category Archives: Living Small

Making Life Better

When I dropped anchor here at Anna Maria Island, FL three years ago I needed a cooler to keep my fresh foods from spoiling. At the time I depended on a small generator (I eventually burned through THREE of them. They AREN’T designed for heavy duty use), so I sprung for a Yeti Tundra 45 cooler. Let me say, after three years, Yeti products are WAY overrated. I could have bought another brand at half the price that receives ratings as good as the Yeti. And the size of the Tundra 45 meant the only place I could put it on my 22-foot sailboat was in the cockpit where it takes up about half of the sole and sits higher than the bench seats. An awkward pain in the ass.

For the past three years I have been buying ten pound bags of ice, on average, every other day. Sometimes, in the heat of August and September I’ve been buying a bag a day. The Yeti will hold 20 lbs of ice and leave a little room left over for food storage. Not the best situation, but one deals with what one has. In the last year, after moving down from the large anchorage by the Bridge Street Pier to the Coquina North Boat Ramp, I have been buying ice at the kiosk at the trailer parking area. It’s the best deal on the island. . .a 10 lb. bag for a buck fifty as opposed to the Circle K two 10 lb. bags for $5. And the kiosk ice is cleaner, purer! Nevertheless, I’ve been spending $40-$45 a month to keep stuff from rotting. But there have been times where the ice has been very low. I’d look at the value of the stuff I need to keep chilled and weigh it against the hassle of rowing to shore, sometimes in trying conditions, and spending the buck and a half and just blow it off.

Readers who follow me know that in the past couple of years I have switched from using a generator to completely solar. Three hundred and ten watts of paneling, in fact. They have done a great job in keeping the batteries for my notebook, iPad, and phone with its wifi hotspot going strong, even on cloudy days. While the huge orange wart in the Oval Office believes that when the sun goes down you can’t watch television if you use solar power, even on the cloudiest of days the panels collect energy and direct it to your battery bank. MUCH slower than on sunny days, but they still collect and store energy.

After doing a lot of online research about 12volt-capable refrigerators I decided that the Ansten 30 liter fridge/freezer would be what I needed. It was compact and would fit inside my boat. The description said it will hold 42 12-ounce cans of soda. Not knowing how much volume that is, I went to the Publix Supermarket and bought my usual weekly supply of perishables. I then went to the canned soda isle and visually checked the volume of the cans with what I had in the shopping cart and the 30 litre fridge would be more than adequate. 

Think about your refrigerator. How much of the total volume of the fridge is simply unused? You have shelves with jars and Tupperware containers and everything above their tops is just empty space. You also store a lot of stuff in there you don’t need to. Things that are heavy on vinegar such as mustard, ketchup, salad dressings really don’t need to be refrigerated despite what it says on the label. Since it’s just ME and not stocking food for a family of five, this little unit fills the bill.

Last week my good friend, Stephen, sprang for the fridge and yesterday I picked it up at my maildrop and wrestled it to its new home. After waiting seven hours to let all the juices settle after the unit had been turned every which way for who knows how long, I turned it on. The digital display (in Centigrade) said that the internal temperature was 86F (30C). In less than half an hour the temperature had dropped to 33.8F (1C)! I’m impressed. And it’s QUIET, too. Certainly won’t disturb my sleep. I was running it through the 110volt inverter because I need to rewire the cigarette lighter outlet before I can use it. The unit cycled a couple of times before the inverter alarm for low voltage went off and I shut it down.

There will definitely be times when there will be problems with this setup. It has been raining off and on all day and night since last Tuesday, and it’s been a challenge to keep the battery bank topped off. There’s been enough for the light stuff as cited above, but the draw from the fridge is a challenge.

While it looks as though Tropical Storm, potential Hurricane, Laura is going to miss us here we’re still going to have a lot of clouds and rain.

Now, as we approach noon it’s heavily overcast and will likely stay that way for the rest of the day and for the next few days to come. Life’s not perfect but there are more sunny days than gloomy ones so I’ll do fine.

 

Comments Off on Making Life Better

Filed under Living off the grid, Living on the hook, Living Small, Minimalist Cruising, Retirement Afloat, sailboats, Small boat kitchen, Small Sailboats, Uncategorized

Staying Aboard

I often write about how I’m confined on my boat anchored here at the lower end of Anna Maria Island, Florida, because high winds prevent me from being able to paddle my dinghy the 130 yards to the boat ramp dock…

But then there are beautiful days like today. There’s a pretty blue sky filled with puffy white clouds and hardly a breath of air. I’m not leaving the boat simply because there’s no reason to. I have food, water and there’s a plague still raging on the land. I’m content being where I am…So I’ll just sit here picking at my ukulele from time to time and arguing with people I don’t know about politics on Facebook.

2 Comments

Filed under Anna Maria Island, boats, Bradenton Beach, FL, Coquina Beach, cruising, Living on the hook, Living Small, Microcruising, Minimalist Cruising, Retirement, Retirement Afloat, Small Sailboats, Uncategorized

A Journey Begun

Three years ago, today, May, 3, 2017, I set out from Ft. Lauderdale, FL., on my little Venture22 sailboat and eventually ended up anchored at the southern end of Anna Maria Island over on the Gulf side of the peninsula.

first day

 

The original destination was to be Breton Island, Louisiana, where I’d worked running a crew boat in the Kerr-McGee oil production field back in ’77/’78. I actually LIVED on the island for nearly a year…working 7 days on and 7 days at home.

Back then the island was about a half mile long and, perhaps, a quarter mile wide at its widest. But over the intervening years hurricanes had reduced it to a sand spit a couple of hundred yards long. I wanted to see it.

breton

I made it as far as Carrabelle in the eastern panhandle of the state.That’s where, 18 miles off the coast, on July 6, 2017, a Coast Guard-dispatched boat took me aboard their boat and dropped me off at the dock in Panacea, Florida where an ambulance was waiting to take me to Tallahassee Memorial Hospital suffering from total kidney shutdown due to severe dehydration. I spent 17 days at TMH and Health South, a rehab facility, until I’d regained enough strength before returning to the boat to continue my voyage. I decided to head south.

rescued

I made it to Bradenton Beach and Anna Maria Island where I’ve been ever since with one excursion, last year, to Cayo Costa to the south. About a 200 mile round trip.

95892932_233310454761404_1467145409381007360_n

92376835_3774458992596645_2369215732702511104_n

Comments Off on A Journey Begun

Filed under Anna Maria Island, boats, Bradenton Beach, FL, Coquina Beach, cruising, Living Small, Microcruising, Minimalist Cruising, Retirement Afloat, sailing, Small boat cruising, Small Sailboats, Uncategorized

The Cruising Life

Some wag once said, “The cruising life is repairing your boat with inadequate tools in exotic locations.” The fact that I have only “cruised” about a third of a mile in the last six months does NOT negate that statement.

I’ve been struggling to remove the original outboard motor bracket on the port side of the transom. The boat had a 25hp Yamaha when I bought it. Much too big and heavy for such a small, light boat as a Venture 22.  It as a lousy engine, too boot. Broke down THREE TIMES between Ft. Lauderdale and Stuart. First time was in Boca Raton, about 20 miles from the start of my venture. It broke down again another 20 miles or so up in West Palm and finally in Stuart. If you searched for the term “hunk of junk” in the dictionary there’d be a picture of that outboard.

I replaced it with an old model 9.9 Mercury outboard. It took me from Stuart, across the state via the Okeechobee Waterway up to Carabelle in the eastern panhandle, and back down to Bradenton Beach where I live at anchor. Last year it took me from here to Cayo Costa and back, a journey of nearly 200 miles. The engine has worked like a charm for close to 2,000 miles. Its single shortcoming is that it’s a “short shaft” outboard and the prop cavitates when I’m rocked with the wakes of other boats and I really can’t use it when the seas are over 2 feet.

To work properly as auxiliary power for these small sailboats the outboards really need to be “long shaft.” Twenty inches, minimum, from where the engine attaches to the motor bracket to the cavitation plate rather than the 15 inches on the “short shaft” outboards. Five inches doesn’t seem like a lot. In fact, most women would scoff at that, but it makes a huge difference with an outboard motor. 

A little over a year ago I bought a second-hand Honda 9.9 long shaft 4 stroke outboard. I had another bracket, sometimes called a “jack stand” that I attached to the starboard side of the transom, and moved the Mercury to it, and put the Honda on the original bracket. 

I just never got the Honda working right. Problem with the idle speed. Since the Merc worked fine I never did what needed to be done to get the Honda working properly. So it sat on the stand for over a year. The bracket was never very good, either. I had to rig it with a block and tackle so I could raise and lower it when the Merc was on it. Over the year as the sailboat rocked and rolled in the wakes of passing boats and waves from storms the engine swayed back and forth on the stand. Sometimes worryingly so. Nothing I did with ropes got it to stay stationary.

I’ve been thinking about getting a BRAND NEW four stroke, long shaft motor for a long time. Actually since from about the time I bought the boat in the first place. But I needed to get rid of the Honda so I’d have a place to put a new motor. I DON’T want a used one. I want something BRAND NEW! I want something that if it poops I can take it in, after using the Merc to get me to the repair shop, and say, “Fix it! It’s on warranty!!!” 

Well, I sold the Honda a couple of weeks ago for almost as much as I paid for it. Damned thing was HEAVY. When it came off the bracket the rear end of the boat rose  a bit over two inches! I know, because the barnacles grow just at the waterline and there were over two inches of the buggers above the waterline with the engine gone.

Then I found that the bracket was frozen. The arms are slightly bent from the side to side action of the motor riding the waves. It’s impossible to raise or lower it. I bought a big breaker bar to try and get the bolts loosened up but no go. So the thing to do was to remove the bracket from the boat and see if I can straighten it out on shore. Easier said than done…

Heaven only knows how old the bracket is. Could be as old as the boat which was built in 1980! It’s attached to the transom by four bolts. Now, since I’m doing this unassisted, I have to slither through a small opening into the space beneath the cockpit seat to get to where the nuts are.

Once through that the space opens up a bit, but not a whole lot. Not enough to be able to sit up, so everything is done lying on my stomach. Here you can see where three of the bolts have been removed.

I got plenty of practice doing this sort of thing working as a rigger at a boatyard in New Orleans. But I’m 36 years older now, have arthritic hands, and less than 40% of normal lung capacity.

If everything goes well, HA! You work your way aft with your wrenches and take the bolt off. Easy Peasy, no? NO! These are lock-tight nuts. They have a plastic insert in the hole so they can’t vibrate loose.

I get the two lower bolts off easy enough. The top, inside nut is on an extra long bolt and the ratchet socket won’t fit over it. Of course I’m not prepared for this. I don’t have a box wrench or pliers with me . The top outside nut turns the bolt so it’s not coming loose.

Here’s why this is happening. Take a look at this more modern bracket.

See how the holes are square? They take bolts like these…

The square shoulders fit down into the squares on the bracket holes. This makes it easy to then go on the nut side of the bolt and fasten the nut without having someone on the outside holding it with a wrench to keep it from turning like happens with THESE…

 

 

Now I have to slither BACKWARDS out into the cabin to work out my next plan of attack. And don’t forget, I have serious COPD problems. I’m operating on about 40% of normal lung capacity so after doing something like getting out of the hole I have to sit for five minutes until my breathing gets back to what passes for normal.

I delve into my tool locker and dig out a pair of Vice Grips and my channel lock pliers. I don’t have a box wrench the proper size.  Over the side, into the dinghy and around to the bracket. I need to attach the Vice Grips to the bolt head. As the bolt is going to turn when I work on the nut, inside, the plier’s handle will also rotate until it comes to rest against one of the arms  keeping the bolt from turning further. OOOOPS. I know from experience that there’s a good chance the pliers might come loose. If that happens they’d fall into the water and be lost. So it’s back around to the side of the boat, up into the cockpit. Rest and catch my breath. Now, where the hell is that ball of twine? I’m not a super organized guy so it takes a while to find it. Back over the side into the dinghy. Around to the bracket. Hold on for a few minutes till my breathing is relaxed again.

After tying the twine to the pliers and securing it to a cleat,  I tighten the pliers onto the bolt head using both hands to lock them on. Back around to the side and up into the cockpit. Sit to catch my breath. Slither into the 16 inch hole and up to the transom. Rest to catch my breath. Use the channel locks to unfasten the nut. When it’s off I take the small hammer and whack away until the bolt end is flush with the transom. That sucker’s really in there. Rest for a few minutes to catch my breath. Agonizingly back out of the pit. Rest. Over the side into the dinghy and back to the bracket. pull the bolt the rest of the way out of the hole and reattach it to the remaining bolt head. Around to the side of the boat. Climb into the cockpit. Rest to catch my breath. Into the hole and work my way to the transom in a motion resembling an inch worm. Rest to catch my breath. Using the channel locks the nut starts working itself off the bolt. CLUNK! The Vice Grips have fallen off the bolt head. SHIT! F WORD! F WORD! F WORD!!!

Out of the hole. Rest. Into the dinghy and back to the bracket. See, I needed that twine. An eighth of a turn on the knob at the base of the pliers and a mighty squeeze with both hands gets them back on the bolt head. Around to the side of the boat, back in the cockpit. Rest. Back into the hole and inch worm my way to the transom. Rest. This time all’s good and the nut’s off. Back out of the hole. Rest. Over the side. Into the dinghy. Back to the bracket. Pull the bolt from the hole. Back to the side of the boat and into the cockpit. Rest. That part of the job is done.

Now I have to pry the bracket off of the transom. It’s stuck on, now, with silicone. Thank heaven it’s not done with 5200 which is the most tenacious adhesive sealant ever created. Silicone has the least adhesive properties of all the sealants, but there’s no telling how much was used when the bracket was attached. In any case, it won’t be easy getting it off. Since the holes on the old bracket are simply round, and not square like the new ones I’m not going to reuse it. I’ll buy a new bracket.

I’ve found a nearby marina down in Longboat Key has four stroke, 6 hp long shafts for sale for $1,650. That’s $200 less than the equivalent Mercury or Suzuki which will cover the cost of a new bracket. And, they’ll bring it up to me. They have to order it first, so it will take a while. Meanwhile I’ll work on removing the old bracket, order and install a new one.

WHEW!

 

1 Comment

Filed under Boat Repair, cruising, Living Abroad, Living on the hook, Living Small, Minimalist Cruising, Outboard Motors, sailboats, sailing, Small boat cruising, Uncategorized

Same Old…

Except for the calendar January 1, 2019 seems just like December 31, 2018. It’s better than January 1, 2018 when the temperature in the morning was down into the upper 30s here in Bradenton Beach, Florida, anchorage. The temperature today is expected to get up into the upper 70s!

did you go out

Comments Off on Same Old…

Filed under Living off the grid, Living on the hook, Living Small, Small Sailboats, Uncategorized

Watch This Spot For Future Developments

I haven’t been sleeping well since the shanty boat bug bit me again. I’ll go to bed and then wake up at 3:30 or 4:00 in the morning as 72 year old men are wont to do, but then when I lay down again my mind keeps churning about all the possibilities of  this venture that I can’t get back to sleep. So a half hour, forty-five minutes later I’m up again and roaming around on the computer.

Here’s one of the hurdles I have to overcome…

Where I Am

As you can see by the yellow stick pin where I am and where the boat should be are quite far apart. Not only that, running right smack between those two pins is the continental divide. A mountain chain thousands of feet high!

I have a complete set of plans for a shanty boat called the Brandy Bar

brandy-bar

It’s 25 feet long and 10 feet wide. That would make it too wide to put on a trailer and truck over the hills to Almirante where it could be launched. The construction is pretty straight forward. It’s like building a house because everything is right angles and no complex compound curves. It would be pretty simple to simply modify the plans and scale the beam down to 8 feet so it would be trailerable.

Another problem is cost. Even scrimping on things like interior design and not counting such essentials as navigation lights, anchors with their chain and rode, regular lighting, cooking facilities, etc., etc., the bare hull would cost around $4K!

Then we get into construction problems themselves. 1) The best source for marine plywood is over there in Bocas del Toro. I live here in Boquerón. For those of you not familiar with boat building, real marine plywood is expensive stuff. Without getting into a big dissertation about how plywood is made I’ll just say there’s “Marine Ply,’ ‘AB’, ‘BC’ and stuff called ‘CDX.’ The letters all refer to the condition of the outermost ply, and the X means ‘exterior.’ All need to have exterior grade glues so the plies won’t delaminate.  The supplier I know of charges $99.95 for a 3/4″ sheet of the stuff. Tack on Panama’s 7% tax and each sheet come in at $106.95. There are approximately 18 sheets needed to build a Brandy Bar or $1,925.00 worth of plywood! He also carries CDX which costs $54.95 for a 3/4” sheet. That would cut the plywood costs to $1,058.33.

Now all that doesn’t include the framing lumber. There are 21 frames that need to be built with 2X6 inch, pressure treated lumber. Each of the frames requires 14′ of the stuff. An 8′, pressure treated 2X6 costs $14.12 (tax included). Each frame is 3′ high, so the lumber for the framing comes in at about $77.00 whether you’re building with top rated marine ply of CDX.

I was also directed, yesterday, to a place that’s supposed to sell plywood in David. What I’ve seen so far has been disappointing, but I’ll check out the new place in the next few days.

And that’s just what the lumber costs. Add in epoxy resins which are far from cheap and which I haven’t even tried to price out though I did find out about a place in David that sells it, fiberglass mat for protecting the hull against ship worms down here (Columbus abandoned two of his boats here in Panama in 1502 because of ship worms). And so on and so on with expenses.

Another problem arises in the building process. You have to build the damned hull upside down on a kind of large jig to hold the framing in place while you’re putting on the plywood sheeting and glassing it all together.

upside downSo, when it’s all sheeted and the fiberglassing is done you have to do this…

flipping itYou have to turn it over so you can build the cabin. And the flippin’ thing is HEAVY right now. (The last two photos courtesy [though they don’t know it yet] of http://littleshantyboat.blogspot.com/ which is one of the best blogs I’ve read anywhere about the actual building process of a shanty boat. If you’re interested in building one you need to bookmark this site.)

So, the other night I was talking to my surfing friend, David, who lives in Costa Rica but who is thinking about resettling, too, in Bocas, when an idea hit me. . .

From time immemorial boats and ships have been built as a single unit. The keel was laid down, frames were attached to that and planking was added to the frames to complete the hull. Instead of building my 25′ long by 8′ wide hull as a single unit, why couldn’t I build, say, units that were 8’X8′ which would be a lot lighter in weight and them, with epoxy, through-bolt those units together? Sort of like putting Legos® together.  Why not, indeed? I mean they build HUGE ships and aircraft carriers that way, now, don’t they?

If they can build something as big as an aircraft carrier in sections and, essentially, bolt the pieces together why couldn’t I do the same thing with something so simple as a shanty boat?

So, naturally, this set me off in other sleepless wanderings around the internet. I found a TON of stuff. From Viet Nam there was this: http://www.hapby.v-nam.net/builds/projects.php,   And this: http://shantyboatliving.com/2012/collaborative-modular-project-post-1/ Plus a bunch more, but you get the idea.

Four Puddle Duck Racers bolted together would make a 16’X8′ hull. Six of them and you’ve got a 24X8. Four of them with a deck covering the top of each one, and joined with spanning  members floored over and you’ve got yourself the pontoons and platform for a pretty large floating home.

And here, too, you don’t have to build it all at once. You can build something large enough (or small enough) to give you a place to live in while you construct further modules. My uncle Dick and his wife Helen lived in the basement of their house in Cincinnati, Ohio while they were building the big house. My secret heros, Jim Kimball and Jay Viola (not to mention their wives who worked just as hard as they did, though in the States) built a fabulous Eco Resort, Tranquilo Bay (http://www.tranquilobay.com/) on the island of Bastimentos  in Bocas del Toro, Panama, piece by piece, and they lived in a TENT on a rickety dock when they started the venture. You really SHOULD read this story, it’s absolutely inspiring about what guts and determination can accomplish…http://www.inc.com/magazine/20080501/paradise-the-hard-way.html I had the good fortune to spend a couple of hours with Jim Kimball a few years ago when I was making my first exploratory trips to Panama and it would be hard to find a nicer person  willing to sit down with a total stranger for a couple of hours and discuss the stranger’s crackpot ideas of building a shanty boat.

So, there you have it. I’m sure there will be many more sleepless nights ahead because of this nonsense. My birthday is only a couple of weeks away. I think this year I’m going to gift myself with some power tools. I’ll show you when I get them.

 

 

 

2 Comments

Filed under boats, Boqueron Panama, Floating Homes, homemade boats, Houseboat, Living Abroad, Living in Panama, Living off the grid, Living Small, Minimalist Cruising, PDR Racer, Puddle Duck Goose, Puddle Duck Racer, Retirement, Retirement Abroad, sailboats, Shanty boat, Shantyboat Living, Small Houses, Small Sailboats

My Shocking Electric Bill

When I lived in Fort Lauderdale my electric bill normally ran around a hundred to a hundred and twenty five bucks a month. Granted, I had the air conditioner running most of the time. It’s about the only way you can survive there for three-quarters of the year. The other three months you need to have the a/c turned to the heat function.

When I was first researching the possibility of retiring to Panama, I read a lot of different blogs and paid special attention to posts about the “cost of living.” People often wrote that one of their largest expenses was for electric service and that the cost per kilowatt hour was higher than it was in the States. Well, you’d probably expect that you’d be needing to run your air conditioning 31 (that’s 24/7) in a country that’s only eight degrees north of the equator. It wasn’t unusual to see people saying that they had monthly bills in Panama similar to what I was paying in Lauderdale.

When I finally made the move it was to a house in Potrerillos Arriba, Chiriqui Province in western Panama. The house didn’t have air conditioning, but at 2,600 feet above sea level it wasn’t necessary. In fact I spent a great deal of the time wearing a sweat shirt to stay comfortable. My electric bill there generally ran about $25 a month. Certainly a bargain compared to what I was used to in Florida and a fraction of what I’d been lead to believe I’d have to pay according to the blogs I’d read.

Boquerón, where I currently live, is 2,000 feet lower than Potrerillos Arriba. The house I rent does have air conditioning, but I rarely use it. The house is small and with the front and back doors open there is generally a nice breeze flowing through. I’m usually comfortable if I’m in shade with a breeze, and when there is no natural breeze one of the two pedestal fans I have works just as well. There are three reasons I turn on the air conditioning. 1) On the first of each month I turn the upstairs unit on for an hour just to make sure it’s functioning. 2) When a neighbor down the street decides to crank up the music and it forces me to close the doors and windows to block out the bass. 3) When I’m using the oven and it heats the downstairs to an uncomfortable level. When the food’s done I shut it off. At night, if I’m not cooking, there are only two lights on and they are the kind conservatives in the U.S. condemn as part of a nefarious socialist plot against their individual freedom to use incandescent lighting. My monthly bill here is pretty much the same as it was in Potrerillos…around $20/month or a bit less.

Last Friday I received my most recent Union Fenosa bill for October’s service. It was shocking! The electric company wants me to pay them $9.87!!! Just so you don’t think I’m pulling your leg, here’s a pic of the bill.

While I came to accept hundred dollar electric bills as normal while living in Florida I also had exceptionally low electric bills when I was living on my shanty boat in Louisiana where it’s every bit as hot and humid in August and September as it is in Lauderdale.

As you can see, I had a window-banger a/c unit but I never used it. Each slip at the marina had its own electric meter. My bill was usually just the minimum necessary to have electric service. It was $7 a month.

One month when I went to pay the bill I stood in line and watched people paying three, four and five hundred dollars just to keep from having their service cut off. The only thing I could think of that would warrant such bills is that they kept their a/c going day and night keeping the temperature of their homes at a level where they could store meat just by leaving it on the kitchen counter.

When I made it up to the window I told the woman, “I’m almost embarrassed to give this to you.”

She looked at the bill and said, “well, you don’t live there.”

“I do,” I told her. “The thing is, when I’m not home the only thing drawing electricity is the refrigerator. If I’m home during the day you can add the television or the stereo. At night you can add a single light bulb.”

The lady took my seven-dollar payment and I left.

One morning, a few days later I was lying on my sofa reading a book (I’d been laid-off at the time). I heard a vehicle crunching down the shell road along the docks. It came to a stop nearby and I heard two doors open and close. Curious, I raised s slat on the blinds and saw two men from the electric company with an instrument testing my meter. The lady at the counter had pimped me out, unable to believe that anyone could exist on seven dollars worth of electricity a month.

The following month I went back to the electric company and paid my monthly seven dollar bill.

 

2 Comments

Filed under Boqueron Panama, Living Abroad, Living in Panama, Living Small, Panama Cost of Living, Retirement, Retirement Abroad

The Ultimate Slacker’s Boat!!!

Murray Stevens instantly became my hero when he designed and built this —

Once again, another fine find from reading:

http://www.duckworksmagazine.com/11/reports/nov/index.htm

2 Comments

Filed under boats, Floating Homes, Houseboat, Living off the grid, Living Small, Microcruising, Minimalist Cruising, Shanty boat, Shantyboat Living, Small boat cruising

PDR Ocean Explorer Weekender

You all know I have a soft spot for the PDR (Puddle Duck Racer). Eleven months ago I wrote a post about how a Finn, Perttu Korhonen, modified the standard 8’X4′ PDR into a cool, but tiny, weekender. http://houseboatshantyboatbuilders.wordpress.com/2010/10/ In today’s issue of Duckworks (if you haven’t bookmarked this great blog, do it now) there was this video of Perttu taking a cruise on Lake Konnevesi. The lake is located in the middle of the country and the whole area seems to be covered with lakes. http://maps.google.com/maps?t=h&hl=en&ie=UTF8&ll=62.613562,26.559448&spn=0.721399,1.774292&z=9&vpsrc=6&output=embed
View Larger Map

I love the Ocean Explorer but I’m not sure I’d want to have one in Finland. I understand that summers are great there. They had it on a Thursday last year. Take a ride with Perttu in this YouTube video…

Comments Off on PDR Ocean Explorer Weekender

Filed under cruising, Living Small, Microcruising, Minimalist Cruising, PDR Racer, Puddle Duck Racer, sailboats, sailing, Small Sailboats

A Couple In A Contessa

Thanks to Greg Joder and his blog Back To Earth for finding this video. It’s a Norwegian couple on a long sail (not yet a circumnavigation) in a Contessa 26. The Contessa is an excellent small boat for the task and is what Tania Abbe chose for her circumnavigation. This boat reminds me so much of my long-lost Nancy Dawson. Both 26 feet long. Both beautiful red hulls. No inboard engine. Windvane self-steering, though my outboard motor mount was on the port side of the transom.

SIGH!

2 Comments

Filed under boats, cruising, Living Small, sailing, Small boat cruising