Category Archives: PDR Racer

Watch This Spot For Future Developments

I haven’t been sleeping well since the shanty boat bug bit me again. I’ll go to bed and then wake up at 3:30 or 4:00 in the morning as 72 year old men are wont to do, but then when I lay down again my mind keeps churning about all the possibilities of  this venture that I can’t get back to sleep. So a half hour, forty-five minutes later I’m up again and roaming around on the computer.

Here’s one of the hurdles I have to overcome…

Where I Am

As you can see by the yellow stick pin where I am and where the boat should be are quite far apart. Not only that, running right smack between those two pins is the continental divide. A mountain chain thousands of feet high!

I have a complete set of plans for a shanty boat called the Brandy Bar

brandy-bar

It’s 25 feet long and 10 feet wide. That would make it too wide to put on a trailer and truck over the hills to Almirante where it could be launched. The construction is pretty straight forward. It’s like building a house because everything is right angles and no complex compound curves. It would be pretty simple to simply modify the plans and scale the beam down to 8 feet so it would be trailerable.

Another problem is cost. Even scrimping on things like interior design and not counting such essentials as navigation lights, anchors with their chain and rode, regular lighting, cooking facilities, etc., etc., the bare hull would cost around $4K!

Then we get into construction problems themselves. 1) The best source for marine plywood is over there in Bocas del Toro. I live here in Boquerón. For those of you not familiar with boat building, real marine plywood is expensive stuff. Without getting into a big dissertation about how plywood is made I’ll just say there’s “Marine Ply,’ ‘AB’, ‘BC’ and stuff called ‘CDX.’ The letters all refer to the condition of the outermost ply, and the X means ‘exterior.’ All need to have exterior grade glues so the plies won’t delaminate.  The supplier I know of charges $99.95 for a 3/4″ sheet of the stuff. Tack on Panama’s 7% tax and each sheet come in at $106.95. There are approximately 18 sheets needed to build a Brandy Bar or $1,925.00 worth of plywood! He also carries CDX which costs $54.95 for a 3/4” sheet. That would cut the plywood costs to $1,058.33.

Now all that doesn’t include the framing lumber. There are 21 frames that need to be built with 2X6 inch, pressure treated lumber. Each of the frames requires 14′ of the stuff. An 8′, pressure treated 2X6 costs $14.12 (tax included). Each frame is 3′ high, so the lumber for the framing comes in at about $77.00 whether you’re building with top rated marine ply of CDX.

I was also directed, yesterday, to a place that’s supposed to sell plywood in David. What I’ve seen so far has been disappointing, but I’ll check out the new place in the next few days.

And that’s just what the lumber costs. Add in epoxy resins which are far from cheap and which I haven’t even tried to price out though I did find out about a place in David that sells it, fiberglass mat for protecting the hull against ship worms down here (Columbus abandoned two of his boats here in Panama in 1502 because of ship worms). And so on and so on with expenses.

Another problem arises in the building process. You have to build the damned hull upside down on a kind of large jig to hold the framing in place while you’re putting on the plywood sheeting and glassing it all together.

upside downSo, when it’s all sheeted and the fiberglassing is done you have to do this…

flipping itYou have to turn it over so you can build the cabin. And the flippin’ thing is HEAVY right now. (The last two photos courtesy [though they don’t know it yet] of http://littleshantyboat.blogspot.com/ which is one of the best blogs I’ve read anywhere about the actual building process of a shanty boat. If you’re interested in building one you need to bookmark this site.)

So, the other night I was talking to my surfing friend, David, who lives in Costa Rica but who is thinking about resettling, too, in Bocas, when an idea hit me. . .

From time immemorial boats and ships have been built as a single unit. The keel was laid down, frames were attached to that and planking was added to the frames to complete the hull. Instead of building my 25′ long by 8′ wide hull as a single unit, why couldn’t I build, say, units that were 8’X8′ which would be a lot lighter in weight and them, with epoxy, through-bolt those units together? Sort of like putting Legos® together.  Why not, indeed? I mean they build HUGE ships and aircraft carriers that way, now, don’t they?

If they can build something as big as an aircraft carrier in sections and, essentially, bolt the pieces together why couldn’t I do the same thing with something so simple as a shanty boat?

So, naturally, this set me off in other sleepless wanderings around the internet. I found a TON of stuff. From Viet Nam there was this: http://www.hapby.v-nam.net/builds/projects.php,   And this: http://shantyboatliving.com/2012/collaborative-modular-project-post-1/ Plus a bunch more, but you get the idea.

Four Puddle Duck Racers bolted together would make a 16’X8′ hull. Six of them and you’ve got a 24X8. Four of them with a deck covering the top of each one, and joined with spanning  members floored over and you’ve got yourself the pontoons and platform for a pretty large floating home.

And here, too, you don’t have to build it all at once. You can build something large enough (or small enough) to give you a place to live in while you construct further modules. My uncle Dick and his wife Helen lived in the basement of their house in Cincinnati, Ohio while they were building the big house. My secret heros, Jim Kimball and Jay Viola (not to mention their wives who worked just as hard as they did, though in the States) built a fabulous Eco Resort, Tranquilo Bay (http://www.tranquilobay.com/) on the island of Bastimentos  in Bocas del Toro, Panama, piece by piece, and they lived in a TENT on a rickety dock when they started the venture. You really SHOULD read this story, it’s absolutely inspiring about what guts and determination can accomplish…http://www.inc.com/magazine/20080501/paradise-the-hard-way.html I had the good fortune to spend a couple of hours with Jim Kimball a few years ago when I was making my first exploratory trips to Panama and it would be hard to find a nicer person  willing to sit down with a total stranger for a couple of hours and discuss the stranger’s crackpot ideas of building a shanty boat.

So, there you have it. I’m sure there will be many more sleepless nights ahead because of this nonsense. My birthday is only a couple of weeks away. I think this year I’m going to gift myself with some power tools. I’ll show you when I get them.

 

 

 

2 Comments

Filed under adventure, boats, Boqueron Panama, Floating Homes, homemade boats, Houseboat, Living Abroad, Living in Panama, Living off the grid, Living Small, Minimalist Cruising, PDR Racer, Puddle Duck Goose, Puddle Duck Racer, Retirement, Retirement Abroad, sailboats, Shanty boat, Shantyboat Living, Small Houses, Small Sailboats

PDR Ocean Explorer Weekender

You all know I have a soft spot for the PDR (Puddle Duck Racer). Eleven months ago I wrote a post about how a Finn, Perttu Korhonen, modified the standard 8’X4′ PDR into a cool, but tiny, weekender. http://houseboatshantyboatbuilders.wordpress.com/2010/10/ In today’s issue of Duckworks (if you haven’t bookmarked this great blog, do it now) there was this video of Perttu taking a cruise on Lake Konnevesi. The lake is located in the middle of the country and the whole area seems to be covered with lakes. http://maps.google.com/maps?t=h&hl=en&ie=UTF8&ll=62.613562,26.559448&spn=0.721399,1.774292&z=9&vpsrc=6&output=embed
View Larger Map

I love the Ocean Explorer but I’m not sure I’d want to have one in Finland. I understand that summers are great there. They had it on a Thursday last year. Take a ride with Perttu in this YouTube video…

Comments Off on PDR Ocean Explorer Weekender

Filed under adventure, cruising, Living Small, Microcruising, Minimalist Cruising, PDR Racer, Puddle Duck Racer, sailboats, sailing, Small Sailboats

A Good Time Had By All

I found this on the Duckworth site this morning in a post by Paul Cook of Las Cruces, NM.

Comments Off on A Good Time Had By All

Filed under boats, homemade boats, PDR Racer

No Group Has More Fun

Anyone who reads my blogs knows I absolutely love the Puddle Duck Racers.  PDRacer.com After all, thier motto is “cheap, creative, and having fun on the water.”

What other sailboat class has a “land speed record” category? So far no one has submitted an entry to this record but I’m sure someone is working on it.

Here are the rules for the land speed record:

1 – Boat does NOT have to be setup in class legal configuration
2 – May use any vertical or horizontal fins, or wheels & attached apparatus such as frame, structures etc. Also the hull may end up only being a cockpit for the land sailor carridge, but that is OK for this challenge.
3 – Skipper must remain in the boat for the entire distance, however all crew may be changed without limitation.
4 – Boat must be propelled by mother nature or human, no motors. Towing with a bicycle is OK, coasting down hill is OK.
5 – For distance record, you may make laps, if you have a GPS that logs distance traveled, you may use that for calculating distance traveled (does not have to be point to point).
6 – For speed record, you can use peak GPS or submit other means that used to calculate speed.
7 – Water must go, or be under the hull at some point in the record attempt. This might be as simple as duct taping a bottle of water under the hull, going over a puddle, or having the final stretch run into the lake.
This record shall be reset at the end of each year.

Rules 4 and 7 are my favorites.

Comments Off on No Group Has More Fun

Filed under PDR Racer

2009 Puddleduck Racer World Championships

It’s hard to believe that any sanctioned group of sailors have more fun with their boats than a bunch of Puddleduck Racers.

The Puddleduckracer 2009 World Championships were held recently in Altoona, Georgia, with participants from 11 states and one foreign country entered.

One of the great parts of the fun is that everyone entered must bring a homemade trophy if they are going to participate. This is the championship trophy:

PDR Worlds 146-wr

David (Shorty) Rouse, the creater of the class captured 5th place and copped this trophy:

Shorty with 5th place trophy

Read a complete account of the Championships here:

http://www.duckworksmagazine.com/09/columns/jackie/03/index.htm

1 Comment

Filed under boats, homemade boats, PDR Racer, Puddle Duck Racer, sailboats

Ultimate PDRacer?

Jason Nabors is a Texan and a big supporter or the whole PDRacer class of fun small sailboats. Not simply content to build the basic boat, Jason has added a lot to the class with sail furling systems and he has raced his Tenacious Turtle, a “cabin” version of the Puddle Duck in the Texas 200.

Who says you have to spend six figures to have fun with boats on the water?

1 Comment

Filed under boats, PDR Racer, Puddle Duck Racer